No. 1366 ISO transport tank, 24,000ltr, 4bar, Melbourne SOLD
ISO foodgrade transport tank, 24,000ltr, New Unused, Melbourne AU SOLD
This unit was purchased new in 2011 for transporting beer but never put into service.
Tank # NTTU.240011-9
Well appointed tank, 316 stainless pressure vessel 6bar design tested & 4bar working, CIP ...
August 2022 certification documents download below.
Contact
- Industrial Brokers Ltd
- ed@ibl.co.nz
- +64 (0) 274 442 944
Terms and Conditions;
- Plant & Equipment is offered on an “as is where is” basis only.
- No warranties or guarantees are offered.
- Sale & Purchase Agreement applies.
- Freight is at the Purchaser's expense.
- Onsite inspections welcome by appointment.
- Site visitor PPE requirements apply.
Manufacturer documentation at the bottom of this page
Technical Specification for Steel Tank Container
Tank Type: 20’ ISO full frame collar tank, Type UN Portable tank T11
Insulated, steam heated, top side rails fitted
Tank No.: NTTU 240011 - 9
Manufacture Date: 01-2012
Specification No. : NT24T11C Rev.0
GA Drawing Ref: 24000/NT001/01/0
Frame Dimensions: 20’ x 8’ x 8’ 6”
Capacity: 24,000 Litres +/- 2%
M.G.W.: 36,000 kg
Tare (est.): 3,650 kgs
Max Payload: 32,350 kgs
Working Pressure: 4 Bar
Test Pressure: 6 Bar
Max. Allowable Vacuum 0.41 Bar
Design Temp: - 40°C to +130°C
Vessel Material: SANS 50028-7 WNr 1.4402/14404(C<0.03%), 316L
Shell: Cold Rolled 2B finish.
Dished ends: Hot rolled and polished internally to 1.2 Micron CLA
Supplied by ALZ, TISCO, Columbus or Outokumpu
Shell Thickness: 4.4mm Nominal
Ends Thickness: 4.7mm Minimum after forming
Corrosion Allowance 0.2mm
Frame Material: GB/T 1591-94-Q345D
Frame to Shell: 304 stainless steel
Corner castings: ISO 1161 - 8 off
Vessel Design Code: ASME VIII Div 1
Radiography: Shell: ASME Spot
Dished ends: ASME Full
Inspection Agency: LR or BV
Cargo carried: See dangerous cargo lists for UN Portable T11 tank
Design Approvals: IMDG T11, CFR49, ADR/RID, CSC, TC, TIR, ISO, UIC, US/UK DOT
Fittings and Accessories: Valve fittings from Item 1 to Item 6 below, supplied by Fort Vale.
1. Manway Assembly 1 x 500 mm - 8-point fastening manlid, low profile with TIR provision Gasket: PTFE encapsulated EPDM inner
2. Relief Valve Assembly 1 x 2 ½” BSP pressure relief valve without flameproof gauze
Set pressure: 4.4 bar
Gasket: PTFE/CNAF
Weld-in pad fitted tangentially inside the centre spill box
3. Relief Valve Provision 1 x 2 ½” BSP pressure relief tank nozzle with bolted blank flange
4. Airline connection 1 x 1.5” BSP air inlet valve with 1 ½” BSP connection fitted with blanking cap and chain. Provision for future fitting of manometer.
Gasket: Encapsulated PTFE
Weld-in pad fitted tangentially inside the rear spill box
5. Top Discharge Provision DN80 weld-in pad with bolted blank flange.
Gasket: PTFE
6. Bottom Outlet Assembly DN80 45° stainless steel high-lift foot valve and clamped type butterfly valve fitted with 3” BSP stainless steel screwed outlet connection and captive blank cap.
Gasket: PTFE/CNAF
An emergency closure cable is connected to the footvalve handle
7. Spill Boxes 2 top spill boxes provided, containing as follows: -
Centre box contains Manway, PR valve and PR provision.
Rear box contains Air Inlet Connection and top Outlet provision
Drainage pipes fitted to each side of each top box
8. Outlet Housing The outlet valve is contained within a protective housing.
9. Walkway ‘F’ type walkway, 475 wide aluminium ‘Q’ grating fitted as follows: -
1 full length walkways fitted with two transverse sections, one adjacent to the centre spill box, one across rear of tank
10. Handrail A collapsible handrail will be fitted along the walkway
11. Steam Heating 6 longitudinal runs of heating coils, giving a total effective heating area of 8.00M2 will be fitted
The working pressure is 4 bar and the testing pressure is 6 bar Inlet and outlet connections are ¾” BSP
Dust caps and chain will be fitted
12. Insulation Tank insulated with 50mm mineral wool with a density of 55kg/M3 where possible. Aluminium foil will be fitted between insulation and tank shell
External cladding: white GRP
13. Thermometer 1 off, analogue thermometer; -40° C to 160° C, fitted on rear end to lower left side
14. Ladder Carbon steel; anti-slip rungs, right-hand rear of tank
15. Earthing Plate 1 off, welded to bottom frame rear end of tank
16. Document Holder 1 off, in tubular PVC
17. Decal Mandatory markings supplied and fitted
18. Data Plate 1 off SS consolidated data plate as per code
19. Calibration Plate No fitted
20. Internal Finish Longitudinal welds: as-welded
Circumferential welds: as-welded but with 300 mm ground flush and polished to a maximum of 1.2 micron CLA on bottom centre line.
Entire internal surface chemically cleaned and passivated after completion of
all welding and dressing.
21. External Finish Tank Shell: External surface of tank cleaned after completion of all welding
and testing.
Framework: All carbon steel frame parts will be shot blasted to Swedish
standard SA2½ followed by the application of:-
22. Painting First coat: Hempadur Zinc (15360) 30 micron min DFT
Intermediate: Hempatex Primer (15300) 40 micron min DFT
Final coat: Hempatex Hibuild (56430) 50 micron min DFT
TOTAL 120 micron min DFT
Colour Blue Black RAL 9005
23. Stacking Each container approved for 10 high stacking